How To Bind A Quilt by Machine

1. Attach Binding to Quilt Back

When attaching binding by machine, begin by sewing the binding to the back of the quilt. Start about three-quarters down on the long side of your quilt. Line up the binding and quilt raw edges.

Clip or pin to the quilt back

Leave a 6″-8″ tail from the end of the binding. This is needed when you are attaching the binding ends.
Use a 1/4″ foot and begin stitching with a 1/4″ seam allowance. Be sure to backstitch at the starting point.

Step 1 in The Beginners Guide To Machine Binding A Quilt is attaching the binding to the back of the quilt.

2. Miter the Corners

The key to beautiful machine bound quilts is what happens in the corners. Follow these steps and you’ll have perfectly mitered corners every time.

Preparing for the corners

Before you get to the corner, stop with the needle down and mark the binding 1/4″ from the edge. I love the Add-a-Quarter ruler for this!

Continue stitching until you reach this line and sew off the quilt at a 45° angle. Remove the quilt from your machine.

Stop 1/4" from the end when attaching binding

Creating a perfect corner

Fold the binding up and away from your quilt at a 45° angle. This will create a triangle in the corner.

To miter a corner, Fold the binding up and away from your quilt

Finish sewing the corner

Fold the binding back down over the corner and line up the raw edges. Pin or clip to hold.
Begin sewing a scant 1/4″ from the top. Be sure to backstitch! This is the magic because it makes your binding fold to the front beautifully.

When binding a quilt, Fold the binding back down over the corner

Where to stop

Continue attaching the binding in this manner. Remember to take your time, especially at the corners. Stop stitching when you’re about 12″ from the starting point.

Continue attaching the binding in this manner until you're about 12" from the starting point

3. Join the Binding Ends

There are several different methods for joining binding ends. Some people match up the ends and straight stitch binding tails. This works fine as long as you lower your stitch length. But it can create a bulky spot on your quilt.

I attach my binding using a 45-degree seam. I like this method because it creates a beautiful, seamless finish. Plus, it’s strong and disperses the seam which prevents bulk in your binding.

Trim the binding tails

This next step is where you need to be precise. Binding strips need to overlap by the same length that they are wide. That means if your binding strips are 2-1/2″ wide, they should overlap by 2-1/2″.

Overlap the two binding ends by width of binding

Mark the cutting line and cut off excess binding tail. Pro tip: I usually cut away an additional scant 1/4″ because it makes the binding ease in better. Once you’ve done this a few time, give it a try!

The Beginners Guide To Machine Binding A Quilt is a complete step-by-step tutorial that teaches quilting beginners an easy way to bind a quilt.

Attaching the binding tails

With the wrong side of the quilt facing up, flip the quilt so the two binding tails are pointing away from you and open up the two binding strips. Note: The placement is very important. If you do the next step with the strips facing the quilt you will end up with twisted binding.

Overlap them at right angles with right sides together. Pin to secure. With a water-soluble pen, draw a diagonal line from corner to corner.

Stitch the two ends together on the marked line and then trim the seam allowance to 1/4″. Notice how the seam is almost invisible. Note: Before cutting, do a check to make sure the binding isn’t twisted.
Press the seam open and align with the raw edge. Finish stitching the binding to the quilt back.

4. Binding to the Front of the Quilt

Time to attach the binding to the front and get that perfect finish! The absolute secret to great looking binding is to take it slowly.

Note: Binding to the front will leave a visible stitching line on the back of your quilt. You will need to use a bobbin thread that matches the back of your quilt and a top thread that matches the binding.

Preparing to stitch the binding down

Wrap the binding to the front of the quilt just past the stitch line. From the middle of the long side, begin securing with Wonder Clips approximately 6″ apart until you get to the corner.
When you get close to a corner, don’t add a clip yet. Go around the corner about 3″ and pull the bottom binding up and over the seam line then add a clip. This will cause the corner to pucker out and make it easy to create a nice mitered corner.

Preparing to miter corners

Fold the bottom binding up and over the seam line and make it go straight across, creating a fold where it meets the other side.

Bring the other side over to meet at the corner. It should form a beautifully matched mitered corner. Put in a pin that goes across the mitered fold to secure.
Continue adding clips to hold the binding, stopping at every corner to create a miter.

Stitching down the binding

Use a 2.5mm – 3mm stitch length and sew down the binding. I use my 1/4″ foot for this, but many people prefer using a universal foot to line up the foot with the edge of the binding and then shift the needle a few stops (if you have this feature on your machine). This keeps your foot firmly on the binding and works exceptionally, especially with a walking foot.

When you get to each corner take one stitch past the corner point, drop the needle, and turn the quilt. Be sure to remove the pin. Continue around the rest of the quilt.

6. Some Practical Tips

This beginner-friendly binding method helps new quilters gain confidence and create beautiful quilts to share and use. It’s ideal for baby quilts or quilts that will get a lot of wear.

Below are a few things I recommend that will help you get better and gain confidence.

When wrapping the binding to the front, make sure to fold your binding beyond your original stitch line. This will prevent you from accidentally stitching over the binding on the back of the quilt.
Use a Walking Foot if you have one available. It will keep your fabric from stretching.
Use a 2-1/2″ binding strip. This will allow room for stitching down the binding.
To avoid skipped stitches and a broken needle, use a Schmetz Jeans/Denim needle (size 100/16).
Use a 50 wt. cotton thread, such as Aurfil.

Note: Watch the short instructional video. It will play automatically.

Get the Printable Post

Want an ad-free, printable version of this post? Click the button below and download the Printable PDF tutorial.

take me to the shop!

How to Bind a Quilt by Machine

Basic Sewing Supplies Needed